Choke And Control Valve (BANDUNG)

Tanggal
04 Okt 2021-07 Okt 2021
09 Nop 2021-12 Nop 2021
07 Des 2021-10 Des 2021

Jam Pelaksanaan
09.00 – 16.00 WIB

Tempat
Hotel Kagum Group Bandung (Golden Flower, Banana Inn, Grand Seriti, Carrcadin, Amaroossa, Grand Serela, Gino Feruci, Verona Palace, Malaka, Zodiac Taurus)

Pembicara / Fasilitator
Ir. Deddy Nugraha is a dedicated experienced fulltime trainer and technical consultant since 2002. He holds a B.S. degree in Mechanical Engineering from ITB, Bandung. He has worked nationally in a wide variety of industries including: technology, aerospace, utilities, auditing, mining and institutions thus engaged as a corporate consultant. He also holds certifications for those particular fields from Snecma, France; Engine Support Inc., USA; Danobat, Spain; DNV, Singapore; MTU, Germany and FAA Auditor, USA. Mr. Nugraha is a member of Indonesian Society for Reliability and was elected as General Sectretay for 2004-2007 period. He has trained hundreds of managers, engineers and floor associates, subjects taught to include; CMMS, RCM, TPM, Project Management, Quality Process Control, Corrosion Control and Protection, Failure Analysis, Engineering Design, Instalation & Constrcution, Inventory Control and Management. Major clients include: Pertamina, British Petroleum, Petrochina, Siemen Power, PT. Indonesia Power, PT. Krakatau Steel, Freeport Indonesia, PT. Surveyor Indonesia, Chevron, Medco Energy, PT. Aneka Tambang, Garuda Maintenance Facility, PT. Perusahaan Gas Negara, PT. Semen Padang, PT. Semen Gresik, PT. Indah Kiat Pulp & Paper, PT. Tjiwi Kimia, PT. Pupuk Kujang and PT. Kaltim Prima Coal.

INVESTATION PRICE/PERSON :

  1. Rp 8. 500.000/person (full fare) or
  2. Rp 8. 250.000/person (early bird, payment 1 week before training) or
  3. Rp 8. 950.000/person (if there are 3 or more participants from the same company)

FASILITAS UNTUK PESERTA :

  1. Modul Training
  2. Flash Disk berisi materi training
  3. Sertifikat
  4. ATK: NoteBook dan Ballpoint
  5. T-Shirt
  6. Tas
  7. Foto Training
  8. Ruang Training dengan fasilitas Full AC dan multimedia
  9. Makan siang dan 2 kali coffeebreak
  10. Instruktur yang Qualified
  11. Transportasi untuk peserta dari hotel penginapan ke hotel tempat training – PP (jika peserta minimal dari satu perusahaan ada 4 peserta)

INTRODUCTION :
This course is a practical knowledge of selection, installation of choke and control valves. Design, specification and implementation of control and operation in gas plant process.

TRAINING MATERIAL OUTLINE :

  1. Basic physical properties
  2. Fundamental of measurement
  3. Fundamentals of flow characteristics
  4. Control valves
  5. Pressure drop
  6. Flow equations
  7. Fundamental valve sizing
    • Introduction
    • Definition of a Control Valve
    • Energy Type
    • What is happening inside a control valve
    • Cavitation
    • Flashing
    • Choked Flow
    • Valve Coefficient Cv
    • Valve characteristic
    • Equal percent
    • Linear
    • Quick opening
    • Selection method
  8. HIGH PRESSURE DROP APPLICATION/CHOKE VALVE
    • Cavitation Control
    • Cavitation Elimination
    • Low Noise
    • Diffuser Plates
    • Chokes
    • Disk Stack Technology
    • Pressure Balance Trim
  9. Control valve selection
  10. Installation